eTrucks.pl • Od 16 lat najlepsze forum z modami do ETS1, GTS, ETS2, ATS, ST
[Blender] brak możliwości zaimportowania modelu - Wersja do druku

+- eTrucks.pl • Od 16 lat najlepsze forum z modami do ETS1, GTS, ETS2, ATS, ST (http://etrucks.pl)
+-- Dział: Wasza Twórczość
(/forum-167.html)
+--- Dział: Modelowanie 3D (/forum-268.html)
+---- Dział: Pomoc (/forum-272.html)
+---- Wątek: [Blender] brak możliwości zaimportowania modelu (/thread-51432.html)



[Blender] brak możliwości zaimportowania modelu - _Y0ogi_ - 13/04/2020 08:27 PM

Witam, chciałem zacząć przygodę z blenderem lecz już na samym początku wystąpiły schody. Mianowicie znalazłem poradnik na forum jak pobrać i zainstalować wtyczki scs do blendera aby importować robiłem wszystko zgodnie z tym poradnikiem odpaliłem blendera i tu pojawiają się schody chcąc zaimportowac model nie mogę tego zrobić ponieważ nie ma opcji do importowana pmd tylko .pim Tak jak już mówiłem dopiero zaczynam fajnie by było gdyby ktoś podpowiedział jak to ogarnąć.


RE: [Blender] brak możliwości zaimportowania modelu - _Y0ogi_ - 14/04/2020 03:22 PM

Image

ktoś wie czego to może być wina ?? czytałem różne poradniki jak prawidłowo ustawić i jak prawidłowo importować ale widzę ze coś poszło nie tak Sad


RE: [Blender] brak możliwości zaimportowania modelu - Mirusox - 14/04/2020 03:50 PM

Here are my questions
1. Which instructions did you follow?
2. Do you write all the necessary path? (check image)
3. Did you use the import .pim or import .scs method?
4. Did you convert the extracted base via ConverterPix if you use import .pim?

Image


RE: [Blender] brak możliwości zaimportowania modelu - _Y0ogi_ - 14/04/2020 04:15 PM

(14/04/2020 03:50 PM)Mirusox napisał(a):  Here are my questions
1. Which instructions did you follow?
2. Do you write all the necessary path? (check image)
3. Did you use the import .pim or import .scs method?
4. Did you convert the extracted base via ConverterPix if you use import .pim?

Image

I use the import .pim method, I converted the extracted database using ConverterPix, set the paths marked by you and still nothing

Image


RE: [Blender] brak możliwości zaimportowania modelu - Mirusox - 14/04/2020 04:36 PM

Install this addon: https://github.com/simon50keda/ConverterPIXWrapper (I dont know if you have it) and try import .scs, import .pim is good when you have a project in progress, when you put folder on converterpix does not always convert all files and so it adds even more work.
when you use import .scs, you must also set project base path, then find and select .scs/.zip folder, and find what you want to import. ConverterPix converts the files that the model needs, but you must to help it with the reflective textures


RE: [Blender] brak możliwości zaimportowania modelu - _Y0ogi_ - 14/04/2020 05:29 PM

don't know, it doesn't work after all. it's hard not to bother with it. Subject to close